Western Digital hard drive installation software

Western Digital hard drive installation software

The Western Digital hard drive can help you to recover the data that has been lost. You can make use of the hard drive to restore the files that you might have lost or formatted accidentally, etc. First, check for the contents in the package, WD hard drive kit, computer system manual, CD, DVD, and SATA host controller drivers. Then, make sure that you have set the jumpers. Now install the driver into the 3.5-inch drive bay. Connect one end of the SATA power cable SATA interface and SATA connector to the motherboard. Follow the instructions of the Acronis True Image WD Edition for the driver installation and management.

How to install Western Digital hard drive

  • First, before you could start the process, make sure that you put on an antistatic wrist.
  • Try to connect the SATA drive to the computer using an expansion card.
  • This performs at speed faster than 1.5 Gbps and make sure that the jumper shunt is on pins 5 and 6.
  • Now, plug in the 7- pin SATA data cable to the rear of the drive.
  • Then, make sure that the other end of the SATA1 cable is plugged into the motherboard.
  • But, if you are using the expansion card, then plug the device into the first slot.
  • Now, search for the 15-pin SATA power cable on the power supply unit.
  • Then, connect the power cable into the Western Digital hard drive.
  • On the computer, make sure to place the drive into an available bay and then bolt the drive.
  • Laptop,
  • First, power off the laptop and then unplug the power cable.
  • Now, make sure that the antistatic wrist band has been put on and then try to push the tabs so that it locks the battery to the end of the laptop.
  • Then, check if the battery pack is removed from the laptop and loosen the screws to remove the hatches.
  • Now, search for the existing hard drive and locate it. If you can find the present drive, remove it from its slot.
  • Pull the hard drive out from the area holding it.
  • Now, ensure that you install the enclosure to the Western Digital SATA drive.
  • Locate the drive in its actual slot and then start to reassemble the computer.

How To Install Wd Internal Hard Drive Windows 10

  • To install the WD Internal Hard Drive on your Windows 10 system, go through the guidelines given below.
  • Before you begin the installation, make sure to unbox your new Western Digital Internal hard drive.
  • Make sure not to unpack the hard drive until you are not ready to install it on your system.
  • Take the Western Digital hard drive out of the static shielding bag.
  • Make sure to handle the hard drive by the sides.
  • Do not touch the circuit board components. Make sure not to remove any tape seal or labels from the hard drive.
  • Now, turn off your Windows 10 system if it is turned On.
  • Remove the cover of the CPU and keep it aside.
  • Locate the empty drive area and slowly remove the mounting sled using your hands.
  • Now, place the new internal hard drive into the mounting sled.
  • Make sure to place the hard drive on the mounting sled.
  • After that, slide the mounting sled along with the hard drive back into the CPU.
  • Now, using the SATA interface cable, connect the hard drive to the SATA port on the motherboard.
  • Similarly, connect the power supply cord to the Power port of the hard drive.Make sure that the connection is done correctly.
  • Close the CPU using with its cover.
  • Now, turn on your computer, click the Start button, and right-click the My Computer option.
  • Select the Manage option in the My Computer menu list.
  • Click the Disk Management option. Perform the instructions displayed on the screen.After that, begin the format process.
  • Once the disk is initialized successfully, right-click on the unallocated space and select the Create partition option.
  • Wait for the Create Partition wizard to appear on the screen.
  • Click the Next button on the Create Partition screen and follow the instructions displayed.
  • Make sure to leave the allocation area as default.
  • Select the desired label in the drop-down menu.
  • Click the checkbox to the Perform a quick format.
  • Select the Next button and click Finish once the hard drive format is done.
  • That’s it. Your new WD internal hard drive is installed on your computer successfully.

How To Install Wd Blue Internal Hard Drive

To install the WD blue internal hard drive on your system, go through the guided instructions as discussed below.

  • Begin the installation process by unboxing the WD blue internal hard drive.
  • Remove the new blue internal hard drive from the static shielding bag.
  • Ensure not to remove any labeling tape from the hard drive.
  • Avoid touching the circuit area of the hard drive. Touching the circuit area may lead to hard drive damage.
  • Take the system cover off, locate the empty hard drive area to begin the installation.
  • Slowly, take the mounted slide out of the system if present.
  • If the mounted slide is not present, then directly place the hard drive into the drive slot, and close the cover.
  • If present, then take the mounted slide out of the system and clip the hard drive into it.
  • Place the mounted slide back into the system and close the cover.
  • Now the hardware installation is done.
  • Turn on your computer, go to Disk Management, and select your hard drive to perform the installation.

How To Connect Western Digital Hard Drive To Pc

To connect your Western Digital hard drive to PC, perform the instructions given below.

  • Get a USB cable to begin the connection process.
  • Locate the USB port of your system.
  • Connect one side of the USB cable to the system and the other end to the external hard drive.
  • Now, double-click the File Explorer icon available at the taskbar.
  • Click the My Computer or This PC option.
  • Now a list of available drives will appear on the left side of the screen.
  • Select & right-click on your external hard drive and click the Format option.
  • Select the NTFS (Default) option in the File System drop-down menu.
  • Click the Start button followed by OK.
  • Wait for the hard drive format process to complete.
  • Once it is done, your hard drive is ready for use.

How to connect western digital hard drive to mac

You need to format the hard drive with the FAT32 file system. Proceed with the following steps to connect your Western Digital Hard drive to MAC.

  • First, connect the WD Hard drive to the computer.
  • Double-click the WD Hard drive icon on the main screen to open it on your computer.
  • Select the Applications option on the left panel of the screen, click the Utilities option followed by the Disk Utility option in the displayed list.
  • Choose your drive from the list in the Disk Utility section.
  • Select the Options button displayed on the screen and then click the Master Boot Record option when the next window opens.
  • Now, click the OK button.
  • Go to Volume Scheme, select the ‘1 Partition’ option, and choose the MS-DOS option from the list.
  • Select the Apply button to save the settings.
  • Click the Partition button when the confirmation window is displayed on the screen.
  • You will see the progress bar on the window. Wait until the process completes.
  • After formatting, the progress bar will vanish automatically.

How to connect western digital hard drive to xbox one

Follow the steps below to connect your Western Digital Hard Drive to Xbox One.

  • Connect the Western Digital Hard drive to the specified port on the Xbox One.
  • If prompted, format the Western Digital Hard drive. If not, close the format window and do the following steps to set the drive as a storage device manually.
  • Click the Settings icon on the main screen and then select the All Settings option on the left panel of the screen.
  • Now, the Settings window will appear on the screen.
  • Select the System option from the displayed list on the left panel of the screen.
  • Select the Storage option on the main panel to open the storage window.
  • Choose your Western Digital Hard drive and then click ‘Format for games & apps.’
  • Now, select the ‘Format Storage Device’ button to format your Western Digital Hard drive.
  • Now, type the name of your drive in the specified field.
  • Click the ‘Install new things here’ button and again click the ‘Format Storage Device’ option.
  • You can now copy, move, and install games and apps to your Western Digital Hard Drive.

HOW TO CONNECT TO WESTERN DIGITAL MY BOOK

  • Before connecting, you have to download the necessary software and
  • configure it correctly.
  • Launch the default Internet browser and key in http://www.wd.com/setup. Tap the Enter button.
  • Choose the My Book Live option from the Welcome To Learning Center window appears on your screen.
  • Select the Go To Downloads option. If you have a Windows system, then click on the Setup.exe file. In case you have a Mac system, then tap the My Book Live Setup.dmg file.
  • Use an Ethernet cable to connect My Book and the router.
  • Connect the power cord between the drive and the power outlet.
  • Open the app you downloaded and tap the Get Started button.
  • Once the LED lamp turns to green, click the Next button on your computer.
  • Choose your My Book device from the succeeding screen and follow the guidelines displayed to complete the setup.
CONNECT TO WESTERN DIGITAL MY BOOK

CANNOT CONNECT TO WESTERN DIGITAL MY BOOK

  • Check if your Western Digital My Book device is connected to the power supply properly. Verify whether the cable is connected firmly to the device.
  • When you are connecting to the system, make sure you do not use a USB hub.
  • Replace the USB cable that you are using to connect if the issue persists.
  • Next, you have to examine the partition available in Disk Management.
  • Find the My Computer icon and right-click on it. Choose the Manage option. Select the Disk Management option from the Computer Management screen.
  • Check if your drive is visible in the next step. Note the partition name of the drive if it is available.
  • If the driver is displayed under Unallocated option, then the drive is corrupted. Delete the partition if it is corrupted.
  • Finally, check the status of the drive. Choose the Device Manager option from the Computer Management screen.
  • Select the Disk Drives option and verify whether your device is listed there.
  • If not, then click the Unknown Devices option and right-click on your device. Tap the Properties option and go to the General tab.
  • If the This Device is not Working Properly message is displayed near your drive, then there is a code 10 or code 28 error with your drive.
  • Code 10 indicates a power supply error, and code 28 represents the drive error.
  • Get support from our technical team if you have any further queries related to this error.